Introduction to international relations Essay Example | Topics and Well Written Essays - 1500 words

Introduction to international relations - Essay Example Neo-classical realism is a combination of both classical and neo realism that accepts both system level and state level natures. Liberalism is a state level theory that believes in the goodness of society. It argues that states try to create peace and cooperation. The last theory is constructivism that claims that the reason behind a particular state behavior is the unique features of the state. Admittedly, in order to understand the America-Vietnam relation, a mere state level theory will be gravely insufficient. The best way to understand the U.S- Vietnam relation throughout the history is to analyze it in the light of a system level theory as the relation was, and is, largely shaped by the international power equations, not because of the special features existed in the nature of America or Vietnam. In addition, neither America nor Vietnam showed even the slightest hint of benevolence, thus proving the unsuitability of constructivism. Thus, the theory that can best explain the rel ation is neo-realism, and a little bit of force can make classical realism too fit for explaining the relations, though inadequate. The tenets of neo-realism Neo-realism is a system level theory and it does not take the individual character of states into consideration. According to neo-realism, the reactions of the states are the results of fluctuations in the international system. As there is no international government that controls the actions of governments, there is total anarchy in the international sphere that makes states always vulnerable to the atrocities by others. Thus, states are always in the effort to gain power in order to protect themselves. However, a rise in power and influence results in more rivalry and more unrest. In this international arena, states have no way other than either defending themselves or attacking their rivals first. A look into history will prove that the American-Vietnam relation was mainly the result of the power movements in the internation al sphere which was mainly bipolar in nature. The America-Vietnam Relation A look into history proves that the American-Vietnam relation can be better understood in the light of neo-realist perspective. The neo-realism, similar to classical realism, argues that all states try to amass power, and that while seeking to increase their own power, they seek to reduce the power of their enemies too. In addition, it is argued in the theory that such states consider other states with power as their enemies. When there is equality of power, peace exists as the players are equal in resources. According neo-realism, the nature of the international system gives birth to power struggles among nations. As Glenn, Howlett, and Poore (2004, 22) state, since there is no world government that controls the movements of national governments, there is total anarchy, and the governments do everything they can to remain secure; hence, when there is a perceived threat to their sovereignty, states either att ack first hand or defend themselves using any possible means they have access to. Admittedly, a look into the America-Vietnam relations will prove that the American intervention in Vietnam was the result of the international power relations that existed at that time, and at that point of time, US had no other option other than the military action. Admittedly, the American interest in the Far East is as old as the National

Project Plan Of Newhall Place Construction Essay

Project Plan Of Newhall Place Construction Essay A brief physical description of the building (including architectural style and the materials used), its history and why it has been granted a listed status. Newhall Place is located at Newhall Hill Birmingham West Midlands B1 3JH. It was built about 1860 and designed by H.R. Yeoville Thomason, who was also responsible for many of Birminghams finest buildings. He designed the Council House and much of Colmore Row. The building was first occupied by a firm of merchants, Shaw Hawkes Co, but by 1871 No. 16 had become the premises of Phipps Pickering and Richard, Brewers. By the 1880s it had become part of the Newhall Wire Works in nearby George Street and is now a Grade II Listed building. This imaginative courtyard development still retains much of this character from 19th Century with exposed beams, arched sash windows and an atrium style courtyard. The durability of an arched window depends on the type of window used and the location, especially how much wear and tear it will receive in that area of the home. There is also the fact that arched windows require special skill in the installation. The contractor will need to frame-in the opening to accommodate the arched design, being sure to install the proper support. He/she should also carefully caulk and seal the arch to create a strong moisture and air barrier. Without a strong seal, your window will require costly repair down the road. (http://www.calfinder.com/library/window/types/Arches-Bring-Style-to-Your-Windows) Every windows and doors have an arch or round on top of them, it seems like a gothic style as specially arranged with brickwork at the outer faà §ade facing the street side. à ¢Ã¢â€š ¬Ã‚ ¦ à ¢Ã¢â€š ¬Ã‚ ¦ à ¢Ã¢â€š ¬Ã‚ ¦ Consideration of the impact of the fixed internal layout of the building on a conversion project, in comparison with modern construction techniques. First of all, most of the historical building preserved has its own characteristics in both architectural or structurally design for purpose and its original use. Although most people may consider to demolish the entire building or alter part of it when come to a project involving change of use or other intend, the existing internal layout usually not capable to accommodate the new design from the architect in terms of modern construction method or techniques in related to the purpose of use. The fundamental problems encompassing the allocation of structure/partition wall, column, beam, staircase, basement, sky light, ceiling/false ceiling, drainage pipe and ducting. In order to retain the front faà §ade which is the major issue to maintain the outlook and architectural feature of historical building, most of the structural elements are not recommended to alter. It is not only not changing the appearance outside but the internal fixed elements would not be suggested to modify since in structural aspect the main structure especially when constructed in brickwork most of the wall, column and beam form the main structural framework. It is easy to notice that those elements are connected to each other in specific joints structure. In most case, it will be more wisely not to touch that part but considering how to reinforce and provide adequate lateral and vertical support to the faà §ade and also the internal structure prior to and during the construction stage. Nowadays, most of the AA works would employ a structural engineer to investigate the existing structure and provide adequate checking in order to determine whether the structures serviceabil ity is strong enough to cater the loading during construction or for future use. One of the key factors of the modern construction in terms of structural stability is spreading the loads by transferring to reinforced concrete column and beam which the load path is much more simple and consistent. With less r.c. structure wall partitions, the space within the entire layout will be enhanced remarkably as well as the flexibility for architect design. Another modern method is to construct a high grade r.c. core wall in the middle of the building like IFC 2 in Hong Kong, the main structure can provide sufficient strength so allow the structural steel elements to attach to and thus the reduction of r.c. beam and column will release more space and headroom. Such structural design can give more flexibility in internal partitioning, where those partitions wouldnt form part of the structure hence future alternation and change of use can be facilitate. To conclude the above, there are much mor e limitations for old design building in compare with modern building in terms of fixed internal layout. Many examples in Hongkong such as 181 shopping mall (former police headquarter in TST) and Murray House in Stanley selected not to ruin the fixed layout but renovate in aesthetic without touching the main structure. c) Consideration of underpinning; waterproofing of basements; upgrading and retrofitting of building services; remedying dampness; repair of masonry; treatment of timber defects. Underpinning First of all, it is recommended to employ a structural engineer to have an investigation over the existing foundations including the main structure, soil bearing capacity, water table etc. First of all, a thorough inspection over the existing superstructure and the basement to reveal if there is any major and apparent crack over the main structure where the temporary supporting system can be determined and also the subsequent main structure reinforcement scheme can be assessed. Secondly, to check over the buried foundation under the basement, adopt trial hole excavation with adequate lateral support at the backyard will be suggested. The fact of the condition of soil and also the existing foundation and the water table could be revealed. Meanwhile the bearing capacity would be obtained by checking with the adoption of method of plate-load test or the like. In our experience, raft foundation should be the most possible existing structure constructed in brickwork for such old building over 150 years. To avoid the disturbance of the existing foundation, it is recommended to have a partial excavation with relative small area in alternative pattern so not to remove too much support from the existing foundation subject to further analysis structural calculation after obtaining relevant data from the inspections. Owing the building is only 2 stories high, thus mass concrete fill could be adopted since shadow partial excavation can be achieved without too many lateral support over the limited space due to the allocation of the building with one side facing the street and two sides abutted to adjacent buildings. Waterproofing of Basement A black, liquid applied single-component moisture-cured bitumen modified polyurethane waterproofing system, which provides superior protection against the penetration of water. Bitumen modified polyurethane elastomer a two-component system is available, which does not depend on atmosphere moisture. Basic uses once cured, the liquid membrane allows expansion and contraction over a broad temperature range and maintains flexibility and waterproofing properties under continuous exposure to water above or below grade. It has a thixotorpic consistency and may be used on vertical as well as horizontal surfaces. The wide range of purposes including application over concrete, stone, brick, cement blocks, wood, metal, asbestos and most other surfaces. After the preparation of the wall surfaces and application of waterproofing membrane, render the wall and screed the floor with one layer of cement sand protective layer. Sump pit system can be adopted in designated location to prevent the failure of the membrane ruin the entire waterproofing system when leakage happen in the future. One layer of extruded polystyrene foam board then be fixed on top of the screed/render to provide a media to reduce the risk of condensation and also enhance the insulation of the entire basement tackle the temperature change. Finally, cover up with a layer of brick (to wall) and the floor with another layer of screed equipped with steel mesh in 2 layers (both top bottom) to form a rigid protective system against external damage to the insulation/waterproofing membrane. Although the space inside will be reduced, still this could be the best waterproofing system to deal with upgrading and retrofitting of building services Electrical Since the entire building used brickwork for construction and structure. To avoid damage or further deteriorate the brickwork, electrical conduit shall be fixed on the existing brickwall without forming a trench for conceal. It may be looking shinning of the GMS conduit finishes but paint should be considered to apply to match with the tone of the wall design. MVAC It is recommended to provide suitable MVAC system to both the upper lower basement due to the confined area below ground level. Installation of ducting within the premises would not be a problem by fixing expansion bolt to the soffit of ceiling. On the other hand, the EAD shall be designed to run along the exterior wall at the backyard to higher level. In order to ensure the architect design and the aim of aesthetic, simply install false ceiling system would make the interior more neat and unify where the exterior pipe/duct can be cladded with aluminum cladding or GRC panel to match with the existing finishes. The Variable refrigerant volume (VRV) system will be selected for air conditioning system based on easy to install, small installation space and easy to repair, the installation methods like the Split-Type Air Conditioning. The Mechanical Ventilation system will install individual the intake and exhaust fan in class room and corridors Fig. xxxx Fire Services To comply with the latest government ordinance and statutory regulation, it is advised that to appoint several design in terms of the followings in FS aspect. To improve the extinguishment and containment system, the ceiling will require install sprinkler system (Fig. xxxxx). Fire rated doors will install between the escape route and corridor area in each floor for isolate the fire occurred. Portable firefighting equipment, included fire extinguishers, fire blankets and sand buckets. Fixed firefighting equipment, included Hose reels, Sprinkler system ,Fig. xxxx, and Firefighting lift Fig: Sprinkler System Plumbing Drainage The major problem will be related to the underground drainage system, what can be seen above ground level should be relatively easier either retain or divert subject to the new architect layout. The u/g drainage shall be redesign subject to the availability of existing sub-structure. It may not be difficult to relocate the existing manhole but it needs to be using the previous opening inside the u/g structure to avoid disturbance of the stability or otherwise too many alternation will affect the overall rigidity of entire structure, subsequently cost/time implication to the project may be enhanced. Part Two. Q1 Your Client has retained your company as Project Managers (offering a full range of services ranging from Professional Design services together with Health and Safety). As a Principal Contractor / CDM Coordinator prepare a detailed Health and Safety Risk Assessment to accompany the tender documentation for the demolition and / or refurbishment of the existing buildings Noise Noise may be defined as sound undesired by the recipient. Besides being a nuisance, noise may interfere with working efficiency, cause accident and most important for resulting in hearing loss to employee. In deciding what the noise control measures to provide, the essential thing is to make a noise assessment to determine what exactly the ideal figure of sound reduction. The sequence will be as below:- Assessing neighborhood noise. Assessing noise (Including noisy plants equipment) generated on site. Deciding the most affected noise sensitive receiver. Comparing the quantitative data calculated from 3 steps before. Making reference to the current statutory regulations. Setting the specific limit. Deciding the noise source. Setting the individual control measure by the means of the following: Substitution (replace equipment with silenced type). Enclosure (enclose equipment by outer wall with inner lining of an acoustically absorbent). Silencers (add). Screens (provide with acoustic screens). Assessing noise level generated on site. Reviewing monitoring the status. Action level can be determined for actions. A report in the prescribed form shall be submitted to the relevant department as soon as possible. For exceeding First Action Level, a warning notice shall be displayed for specification of distance for noisy machines or tools. Between First and Second Action Levels a daily personal noise exposure between 85 and 89.9 dB(A), when employees are exposed, the site are required to provide suitable approved ear protectors to employees who request for them. Between Second and Peak Action Levels a daily personal noise exposure of 90 dB(A); a peak sound pressure level of 140 dB or 200 Pa, the site are required to provide suitable approved ear protectors to employees and enforce them to use properly. Having finished each assessment, a list will be generated to inform all subcontractors how far are the hearing protection zone are. The General Foreman / Foreman should post noise labels and follow the rules in the different action levels. Dust Dusts usually fall into three groups when considered as hazards. They are toxic, nuisance and fibrosis producing. Adequate ventilation, efficient dust suppression, good housekeeping and proper personal protection are required to control dust explosions. Basically, substituting a less dangerous material for those from which dust arises is a method to control. To arrest the dust and collect it as near as possible to the point of origin, local exhaust ventilation is needed to install. To be effective, a mask must be fitted carefully and must be kept clean and the filter must be replaced when necessary. To enclose a work process that produces dust is also a method we can take. In spite of all precautions, some dust will always escape from the plant. It must be prevented from accumulating in workrooms by the regular and frequent cleaning of all parts of rooms and plant. First-aid Facilities Adequate number of first-aider and facilities in accordance with the law should be provided on site. It may have saved the casualtys life through the application of appropriate first aid measures. However, his life can be lost through rough handling or careless transportation procedures. Before you attempt to move the casualty. Housekeeping The laws including F IU Ordinance Regulations, Air Pollution Control Ordinance (Cap. 311), Occupational Safety and Health Ordinance, Construction Sites (Safety) Regulations, Air Pollution Control (Open Burning) Regulations and Air Pollution (Construction Dust) Regulations demand us to have a good housekeeping. The common hazards on site are openings, projecting nails or metal fragments at dumping area etc. Removing debris frequently is better than dealing with them after being stacked to a large amount and has advantages both in save time and money. Rag, oil, grease should be regarded as chemical waste. Waste paper or cans should be kept in rubbish bin, which is removed immediately if full. Waste reinforcement or other valuable materials should be saved in a particular place. All tools or equipment should be kept in storeroom after used. A safe means of access shall be maintained up to the required standards. Removing projecting nails as quickly as possible. Demolition Effective planning and monitoring are required to ensure that the demolition process or the partially demolished elements left at the end of each day of work does not pose any danger to the works, the general public and the adjacent properties. The General Foreman / Foreman shall provide all necessary precautionary measures to protect the works, the building, the occupants, the public and other prior to commencement of the demolition works. The General Foreman / Foreman shall ensure the means of escape provisions as well as fire compartment of the premises are maintained throughout the Contract period both for the renovation area and the adjacent tenancies.. Stability Report Including Calculations A report on the stability of the building to be demolished is required during all stages of demolition if necessary. Temporary Supports When temporary supports to structure is required, check the entire scaffolding assembly and utilities before demolition. Housekeeping Material shall be properly stored. Access ways and work areas shall be free of obstructions. Waste shall be properly disposed of at least daily. Do not overload any members. Dangerous Zone Cordon off any identified dangerous zones. The site shall be locked up all the time. In order to avoid trespasser, the General Foreman / Foreman shall inspect the premise each shift prior to work. Utilities Permit-to-work system is activating. Electrical Safety All electrically powered equipment or hand tools, except double insulated hand tools, shall be grounded. Portable hand tools and electrically powered equipment shall be used with a circuit breaker. Electrical equipment shall be disconnected or the current otherwise interrupted while it is being adjusted or repaired. Outlets, switching, junction boxes, etc. shall be covered. Exposed noncurrent-carry metal parts of fixed equipment that may become energized under abnormal conditions shall be grounded when in wet or damp locations. After demolition Clear away all debris. Secure boundary unless reinstatement has been made. Provide a Method Statement for the key stages of the entire project and a Construction Program identifying the key stages (i.e. this is not a definitive list) demolition, faà §ade retention, temporary works, high water table etc. Foundation Underpinning 1) Excavation shall be proceeded with respected to the structural engineer for adequate depth and the sequence prescribed. 2) Lateral support shall be followed according the same manner to the desire depth. 3) Concreting to the module of foundation as designed in alternative. 4) Backfilling at not more than the specified depth of each layer, shoring shall be dismantled successively. Ground water control In some cases, the ground water conditions found during site investigation may change before or during site investigation. Such changes may be due to the construction of basements nearby, natural flooding or artificial causes, such as a burst water main. The methods of ground water control may be divided into three broad groups: pumping, cut-off walling, and special methods. The choice of method depends mainly on site conditions and on the soil characteristics. These include:- size and location; thickness and type of soil strata; magnitude of water pressures in various strata; proposed permanent structure relative to soil strata; length of time for which the excavation must be open; prevention of damage to adjacent structures; relationship between the proposed dewatering method and the construction sequence. Dewatering Pumping from sumps Widely used in deep excavations for trench or basement. There are several major problems:- Soil movement due to settlement Ground affected by water flow towards sump Instability at formation level in timbered excavations owing to upward movement of water The general solution is to dig sump at corner of excavation below formation level. Open Sump The sump is usually formed away from the construction area in a corner of the excavation. The water is led into the sump, either by sloping the ground towards it or by using shallow garland drains which feed into the sump. Pumping from open sumps is limited to a maximum depth of about 8m. Jetted Sump In this method, a hole is formed in the ground by jetting metal tube. A disposable intake strainer connected to a disposable flexible suction pipe is then lowered into the hole, and the void filled with sand filter media. This suction pipe is connected to a pump which pumps out the ground water. Demolition 1) Temporary support such as racking shore shall be installed at each floor prior to any demolition work commence. Demolition Work 1) Statutory and contractual Requirements shall be followed and implement on site at all time. 2) All demolition works shall be carried out in accordance with the Building (Demolition Works) Regulations, the Draft Code of Practice for Demolition of Buildings as well as Building Department Practice Notes. 3) Before any demolition work is commenced, a sufficient survey for proper identified of any structural problems and risk associated with flammable and hazardous substance, utilities etc. 4) Location of Utilities 4.1) The whole area, which is affected by any possible demolition works, shall be identified. 4. 2) Plans or other suitable information about all utilities especially concealed pipes in the vicinity of the proposed works before any demolition work starts shall be obtained. 4.3 ) Shut off, cap, or otherwise control all electric, gas, water, sewer and other service lines before demolition work is started. Permit-to-work system shall be activated. 4.4) If it is necessary to maintain any power, water, or other utilities during demolition, such lines should be temporarily relocated as necessary and/ or protected. 4.5) plan on the proposed methods for handling and disposal of debris including the permissible temporary accumulation of building debris and the transportation route shall then be evolved. 4.6) Stability Report with supporting calculations shall be generated. Faà §ade Retention 1) To design by the structural engineer with the project manager to investigate the most economical and efficient method prior to determine the sequence of work. 2) Provide suitable foundation at ground level and erect the steel prop above the temporary footing. 3) Continued with the diagonal bracing and transom to form a stable framework floor by floor from bottom and up sequence, make sure the bolting is securely fixed. 4) Floor slab shall be hacked off to let the framework going up and through the slab. 5) The configuration of framework will be similar to fly racking shore. Your Client is also concerned that they discharge their statutory obligations under the CDM Regulations, in addition to the Health and Safety Risk Assessment. Explain the workings of the CDM regulations and how these affect them as developers throughout the entire contract (i.e. demolition, new build and refurbishment). The clients duty in relation to the health and safety file (1) The client shall ensure that the CDM co-ordinator is provided with all the health and safety information in the clients possession (or which is reasonably obtainable) relating to the project which is likely to be needed for inclusion in the health and safety file, including information specified in regulation 4(9)(c) of the Control of Asbestos Regulations 2006(a). (2) Where a single health and safety file relates to more than one project, site or structure, or where it includes other related information, the client shall ensure that the information relating to each site or structure can be easily identified. (3) The client shall take reasonable steps to ensure that after the construction phase the information in the health and safety file (a) is kept available for inspection by any person who may need it to comply with the relevant statutory provisions; and (b) is revised as often as may be appropriate to incorporate any relevant new information. (4) It shall be sufficient compliance with paragraph (3)(a) by a client who disposes of his entire interest in the structure if he delivers the health and safety file to the person who acquires his interest in it and ensures that he is aware of the nature and purpose of the file. In anticipation that a project comprising of demolition, alteration and refurbishment, will proceed based on your recommendation, advise on the scope and nature of the project team. This should include the timing and sequence of appointments. Designer/Architect Consultants To provide design of the architectural layout, featuring, what to be retained or demolished To provide detail information about the aesthetical features, design of lighting, furring and finishing to internal/external area. Professional Structural Engineer To provide structural calculation and analysis for the followings: Soil bearing capacity and foundation upgrading design Inspection to the substructure elements with remedial proposal Inspection to the superstructure elements with remedial proposal Temporary lateral support for foundation work Vertical/lateral support for the retention of faà §ade unit and/or structural elements 4. The Building Team Building is a group activity and its success depends on a good understanding and operation between a large number of people. The participants involved can be conveniently arranged into groups or teams according to their particular interest and /or involvement as follows:- 4.1 Client Team The client or the building owner has the responsibility for defining the building to suit needs, establishing and providing the necessary finances, agreeing design and construction phases, timetabling, and, of course, fulfilling the management and running of the completed project. A potential client must establish whether to build or not to build. Having decided that a new building is necessary to provide additional or alternative space, it is important that consideration is then given to when the space will be needed. Various problems are needed to be solved, such as: land acquisition, establishment of rights, development permits, planning permission, building approval, contractor selection and subsequent erection. Most building is undertaken from money made available in the form of a loan therefore, interest rates are important. In this respect, the government has direct influence and can use the building industry as a regulator for the economy of the country. Once the money becomes available for a building, the client will require speedy action for its design, construction and subsequent use so that the lost interest, which would have been gained through alternative financial investments, may be speedily recouped. The total cost of a building must include the professional fees of the Design Team which the client appoints. 4.2 User Team User Team forms a vital link between design concepts and built reality. An example of User Team is the advisory organization formed by the tenants of public housing. 4.3 Design Team There are a great many people in a Design Team who concerned with supplying the design expertise which will make a building possible. Principal Designers generally include architects, interior designers, and building surveyors. They are responsible for the overall design of the project. Architects design and prepare the production information for most building projects. They will also inspect the construction work on site. Interior Designers can also prepare design and production information for a building, and provide supervision of work, but, they may be specifically concerned with the interior of a building and need additional advisers in order to deal with all the design and construction processes involved in total building. Building Surveyors are sometimes responsible for the design and supervision of certain building work although they are more usually carry out surveys of structural soundness, condition of dilapidation or repair, alterations/extensions to existing buildings and market value of existing buildings. Specialist Designers include civil and structural engineers, services engineers, and those concerned with specific aspects of architecture, including landscape, interiors, office planning, etc. They provide expertise concerning certain aspects of a building and whose requirements are often coordinated by the Principal Designer. For example: HVAC Communications Drainage and plumbing Electrical Fire services Security systems Civil and Structural Engineers are employed to assist Principal Designers on building projects which contain appreciable quantities of structural work, such as reinforced concrete, complex steel or timber work, or foundations which are either complex or abnormal. Services Engineers work with other designers and are concerned with environmental control lighting, heating, air conditioning, and sound modulation; electrical installations, plumbing and waste-disposal systems; and mechanical services, such as lift installations and electrical conductors. Quantity Surveyors provide the cost control and financial advice to client, principal designers and specialist designers. They are responsible for preparing Bills of Quantities. Also, during the actual construction period for a project, he must measure and value the work carried out at regular (monthly) intervals and submit details to the overall financial administrator (usually the principal designer) for payments from client to contractor. They also advises on the use of sums of money listed in the Bill of Quantities for contingency or provisional items, the cost of making variations in areas originally described in the Bills or indicated on the drawings, and settlement of the final account for the finished project. Depending on the precise nature of a project, the combined cost of these professional fees will vary from between 12% and 20% of the final construction costs. 4.3 Research Team Researchers are those making understanding and development of current construction methods (materials and technical ability). The aim of the research is to discover facts by means of scientific study and, in matters concerning building, covers a very wide area of knowledge requiring controlled programming of critical investigation of chosen subjects. 4.4 Legislative Team They negotiate with the relevant authorities to clarify certain legal requirements. Building Ordinance Office, Planning Department, Fire Services Department, Highways Department, Urban Council, etc. On site management level, a builder has to ensure that the building site maintains safe and healthy conditions for employees, and that the general public should be adequately pro

Just War :: Essays Papers

Just War What makes a just war? As you ponder this question, you ask yourself is there really a correct answer? The word "just" contradicts every aspect of war. Can a chaotic and brutal event, such as warfare, be guided by reason and fairness? During the height of the 12th and 13th century in Europe it was thought that every war should be fought for a just cause. It was during this time that the concept of chivalry arose, creating a sense of honorable and courteous conduct expected among knights. Knights were to feel a personal obligation to the weak and defenseless elements of their society. Therefore it became a knight's duty to fight off anyone causing harm to the helpless people of his society. The notion of fighting for the good of society thus became a just cause for war. The ideas of chivalry came about through the church in an effort to Christianize the military. The church made a knight take an oath that his sword "may be a defense of churches, widows, orphans, and of all those who were not entitled to bear arms." Books were also written that marked out the rules of chivalry in more detail such as The Order of the Hospital of St. John of Jerusalem and The Order of Poor Knights of Christ. The books stated things like, "protect churches and ecclesiastical property, unarmed women, non-noble children under the age of fourteen, and unarmed clergy peasants engaged in their labors." The rules of chivalry gave a purpose to fighting. War was honorable because it was for the protection of helpless people. Those who fought for the good of society were fighting for a good and just cause and would be looked highly upon in the eyes of God. The rules of chivalry also applied to the other side of warfare. Knights who were fighting had to follow honorable rules when dealing with the enemy. A chivalrous knight would not harm the weak or the defenseless people during warfare. In this way war became "fair" because only the armed would fight. The rules of chivalry became commonly understood social laws. Knights followed the rules of chivalry because it made them honorable, good men and pleased the Lord.

I Love to Travel Essay

I’ve decided I want to travel. I mean I’ve always wanted to, but now I’m going to start planning it. I think once I finish University I’m going to take a year off, and travel the world. Visit different countries, move from town to town, live and experience different cultures. I’m not going to go straight into work after Uni.. I want to live my life. I mean I’m ready to leave this country right now, get away from everyone and just learn to be independant and travel†¦ but I have priorites at the moment, and for the next few years. And while it seems like a while away, a few years will pass quickly and I will be on my way to living in Paris for a while in a cute little apartment with the Eiffel Tower at your windows view, the busy streets of New York.. the sunshine of LA.. I’ll be dancing with the Spanish, learning the local life of Greece, seeing beautiful places and monuments in Italy and learning the life of Tuscany.. When you live in one country your entire life, you learn to think it’s all that’s out there.. his little world of yours. But it’s not. Once you come to realise there’s a whole world out there left to explore, something inside of you just craves it.. craves knowing and understanding and learning and seeing.. I want to see the world, before I work and settle down and do whatever.. And I don’t care if I’m on my own. The years of my 20s will be finding myself. Establishing myself. Making the most of discovering who I am and the world out there.

Perfume Essay

This essay will compare and contrast the various methods used by the author and director of the novel Perfume. Perfume, written by Patrick Suskind and adapted by Tom Tykwer, is a dramatic, crime thriller about the life of a murderer. Born and raised in Paris, Jean-Baptiste survives the most gruelling childhood; his father unknown and mother executed for attempting to kill him, rejected by the wet nurses in the village and when finally taken in by Madame Gaillard at the orphanage, the children endeavour to kill him. They fear he is dangerous because of his lack of personal scent. However Grenouille survives through even their best efforts, survives the measles, dysentery, chicken pox and cholera. It is clear that this child is special not only because of his amazing ability to endure the most appalling conditions but also because of his exceptionally talented sense of smell. The title â€Å"Perfume† gives the reader/viewer a good idea of what to expect from the very beginning. Trying to translate Grenouille’s olfactory language into visual picture was from the beginning a mammoth task than is expertly accomplished by the director through the use of audio and several visual components. It is however much easier to do in a book because the reader can be manipulated through their personal experience with smell. Therefore from this point the book is mildly better even though it is at a disadvantage because the reader has no visual aid. The main themes of Perfume are black humour, emotionally/mentally challenged people, hatred of humanity and seeing importance in others life only when they affect your own. These themes are portrayed well throughout both the book and film. The most prominent is seeing importance in others life only when they affect your own. For example, Madame Gaillard dies in a tragic way shortly after she sells Grenouille. In the book she dies of cancer in a crowded bed, in the film she is slit at the throat as she returns home. Monsieur Grimal falls into the river on his way home from celebrating the sale of Grenouille. Giuseppe Baldini’s house falls into the river not long after Grenouille leaves for Grasse. All these deaths symbolise that Grenouille can only value human life if it has something to reward him with; when this is done they no longer exist in his mind. This also explains why Grenouille can kill the innocent girls, take what he wants and leave without feeling any remorse for his actions. One of the best adapted scenes is the opening chapter, Grenouille’s birth. Suskind does an extended description of the putrid place where Grenouille was born. â€Å"The streets stank of manure, the courtyards of urine, the stairwells stank of mouldering wood and rat droppings, the kitchens of spoiled cabbage and mutton fat†, this quote goes on for a considerable amount of time yet it is necessary because there is so many rotten smells included that everyone can relate to at least one. This provokes the reader to think of the most revolting smells they have ever experienced and then try to imagine them worse. In the film, Tykwer uses a fast moving, rolling shot to show the reader the various scents that inhabit the area. And he uses shots of typically revolting objects such as rats, fish guts, sick and rotting vegetables. These smells are relatable to humans and so the viewer can appreciate how bad it smells, however this may not be as powerful as the smell that the human imagination can fabricate from the book. Also he employs the sound of a heartbeat and rapid breathing of the new-born babe to humanise the situation and to portray the struggle the baby has to survive. The heartbeat makes us anxious and so we wonder whether the baby will survive. The baby breathing rapidly makes us question if it can continue. However regardless of this the baby lets out a scream. The audio effects stop and this could symbolise that as soon as the baby chose to live it ended the life of his mother and shows that the world is not the same. Obviously some scenes from the book have had to be cut to stay within a reasonable screen time, one of the scenes cut is the scientific study that is carried out on Grenouille nevertheless this is not missed and the film makes up for such scenes in other aspects. One of the biggest advantages the film has over the book is that it can use the best actors suited to the role. The actor that plays Grenouille, Ben Whishaw is perfectly suited to the character. He has a childlike voice that represents his innocence, not that his soul is innocent but because he has been void of all love for his whole life. His life was only valued by those wanted something from him. His character is also very good because his expression can be changed in an instant. In one scene he can appear helpless and angelic while in another he can be closer to the devil than a human. The way he sets himself into the role is nothing less than perfect; he scuttles as he should, hunches as he should and does everything as weirdly as is should be. Grenouille is a disturbing character and this is very well portrayed by the actor. In the book Grenouille doesn’t say much because the book is written in third person. This is used so that the reader can get close into the minds of all the characters instead of being limited to one. This also means that we can observe events happening in all the different places. In the film this is done through the use of a narrator. However the narrator does tend to disclose information that as viewers might have preferred to interpret ourselves. So even though the narrator is used in both the book and film the effects are far better in the book. To conclude, there are many similarities between the book and film adaption of Perfume that are equally as good as each other but some aspects such as the narrator are stronger in the book. Equally particular aspects of the film are better, for instance the ability to use actors. One of the primary differences is the character change of Grenouille from book to film. The book shows him as a conniving parasite that is very good at manipulating people. The film shows a man who is unaware of the effects of his actions and is somewhat innocent. The strongest parts of the book are the descriptions of the in-depth break down of the various scents and how deep into Grenouille’s mind the reader gets, since spoken language is not Grenouilles strength. The best bits of the film are casting decisions and the superb adaption that captures the soul of the book and enhances it through captivating music and images. It’s like smelling with your eyes.